Product ID:GLOSS SILICONE ALKYD ENAMEL
MSDS Date:02/10/1989
FSC:8010
NIIN:01-211-1103
MSDS Number: BQCYD

Emergency Phone: 206-941-1619

Info Phone: 206-244-8844

Cage: 2F266

Telephone: 206-244-8844

Cage: 6F266

SOLVENTS, ALIPHATIC HYDROCARBON (MINERAL SPIRITS) (VAPOR

CAS: 8052-41-3

RTECS: WJ8925000

Fraction By Weight: 35-40%

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM; 9293

Health Hazards Acute and Chronic:EYES: SEVERE IRRITATION, REDNESS,
TEARING, BLURRED VISION. SKIN: (PROLONGED/REPEATED); IRRITATION,
DEFATTING, DERMATITIS. BREATHING: NASAL & RESP IRRITATION,
DIZZINESS, WEAKNESS, FATIGUE, HEADACHE, UN CONSCIOUSNESS,
ASPHYXIATION. INGEST: GIIRRITATION, NAUSEA, VOMITING, DIARRHEA,
PNEUMONITIS.

First Aid:SKIN: WASH W/SOAP & WATER. REMOVE CONTAM CLOTHES. EYES: FLUSH
W/LRG AMT WATER, LIFTING EYELIDS OCCAS. GET MED AID. INGEST: DONT
INDUCE VOMIT. KEEP WARM, QUIET, GET MED AID. ASPIRATION OF MAT'L
INTO LU NGS (VOMITING) CAN CAUSE CHEMICAL PNEUMONITIS (CAN BE
FATAL). INHAL: REMOVE TO FRESH AIR. IF BREATHING DIFFICULT, GIVE
OXYGEN. IF STOPPED, GIVE ARTIF RESPIRATION. KEEP QUIET & GET MED
AID.

Flash Point Method:TCC
Flash Point:100F,38C
Lower Limits:1.0
Extinguishing Media:FOAM, DRY CHEMICAL, CO2
Fire Fighting Procedures:SELF-CONTAINED BREATHING APPARATUS WITH A FULL
FACEPIECE OPERATED IN PRESSURE-DEMAND OR OTHER POSITIVE PRESSURE
MODE.
Unusual Fire/Explosion Hazard:NEVER USE NEAR OR AROUND WELDERS OR
CUTTING TORCHES. DRUMS (EVEN EMPTY OR ONLY WITH RESIDUE) CAN IGNITE
EXPLOSIVELY.

Spill Release Procedures:SMALL: SOAK UP WITH ABSORB. LRG: ELIM IGNIT
SOURCES. STOP SPILL. DIKE AREA, PUMP LIQ TO SALVAGE TANK. PREVENT
RUNOFF TO WATER BODIES. NOTIFY PROPER AUTHORITIES AS REQUIRED.

Handling and Storage Precautions:CONTAINERS OF THIS MATERIAL MAY BE
HAZARDOUS WHEN EMPTIED, SINCE EMPTIED CONTAINERS RETAIN PRODUCT
RESIDUES (VAPORS, LIQUID, AND/OR SOLID).
Other Precautions:ALL HAZARD PRECAUTION GIVEN IN THE DATA SHEET MUST BE
OBSERVED.

Respiratory Protection:IF TLV OF PROD/COMPONENT EXCEEDED, NIOSH/MSHA
AIR SUPPLD RESPIRATOR ADVISED. OSHA REGS PERMIT OTHER NIOSH/MSHA
RESPIRATORS UNDER SPECIFIED CONDITIONS (SEE SFTY EQUIP SUPPLR).
IMPLEMENT ENGINEERING/ADM INSTRATIVE CONTROLS TO REDUCE EXPOSURE.
Ventilation:PROVIDE SUFFICIENT MECHANICAL (GENERAL/LOCAL EXHAUST) VENT
TO MAINTAIN EXPOSURE BELOW TLV(S).
Protective Gloves:WEAR RESISTANT GLOVES (NITRILE RUBBER).
Eye Protection:CHEMICAL SPLASH GOGGLES, SAFETY GLASSES
Other Protective Equipment:TO PREVENT REPEATED OR PROLONGED SKIN
CONTACT, WEAR IMPERVIOUS CLOTHING AND BOOTS.
Work Hygienic Practices:KEEP WORK AREA CLEAN & FREE FROM LEAK & SPILL.
ALWAYS WASH HANDS THOROUGHLY W/SOAP & WATER BEFORE HANDLING FOOD &
DRINK.
Supplemental Safety and Health

HCC:F4
Boiling Pt:B.P. Text:300F,149C
Vapor Density:> AIR
Spec Gravity:10.87 LBS/GAL
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:NIL
Appearance and Odor:THIXOTROPIC LIQUID WITH A MILD SWEET AROMATIC ODOR
Percent Volatiles by Volume:50

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:KEEP AWAY FROM OPEN FLAMES, SPARKS, &
HEAT. DO NOT WELD NEAR OR AROUND PRODUCT.
Conditions to Avoid Polymerization:KEEP AWAY FROM OPEN FLAMES, SPARKS,
AND HEAT. DO NOT WELD NEAR OR AROUND PRODUCT.

Waste Disposal Methods:DESTROY BY LIQ INCINERATION. CONTAM ABSORB MAY
BE DEPOSITED IN LANDFILL IN ACCORDANCE WITH LOCAL, STATE AND
FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.